Checkout: £0.00
Click to zoom
Please Note: Computer screens and printers do not render colour consistently. Our “Lakes and Fells Collection” colours are made to order (Excepting White & Magnolia) so ordering a tester pot is highly recommended to check your colour preference accurately, before making your final choice.
Born in the unforgiving fells of Cumbria, Weatherflex doesn't just survive British weather; it thrives in it. While ordinary masonry paints crack, fade, and fail, Weatherflex flexes with your walls, repels the worst storms, and keeps looking beautiful year after year.Read More
Due to ADR regs on transport of flammables we can only send 25L drums of solvent product via premium rate special carrier, hence minimum FREE carriage order is 4 x 25L or ring for a quote. Alternatively, you can still collect single 25L drums at our Ulverston or Glasgow trade counters.
phone01229 869100
We would only use this to contact you to discuss your experience with our products.
Our advanced polymer formula stretches over 100% without cracking. While rigid paints shatter under thermal stress, Weatherflex moves with your building, bridging hairline cracks and preventing water damage before it starts.
The perfect balance: keeps rain out while letting trapped moisture escape. Our microporous technology prevents the damp problems that plague other "waterproof" coatings.
Made with superior-grade polymers and UV-stable pigments. Not the cheapest option, but the last paint job you'll need for over a decade.
The materials which make up Weatherflex are carefully selected for their long-term performance to create a waterproof masonry paint that performs in extreme conditions.
From Welsh valleys to the Outer Hebrides, Weatherflex protects:
If it can handle a lighthouse in a Force 9 gale, it can handle your house.
One paint, endless possibilities:
Apply with brush, roller, or professional spray equipment for that perfect finish.
Our contemporary colour palette captures the natural beauty of the British countryside. Each shade is carefully formulated to harmonise with both traditional and modern architecture.
"Applied Weatherflex to our 200-year-old Cumbrian cottage five years ago. Still looks like we painted it yesterday, even after some brutal winters."— Sarah M., Kendal
"Used it on our commercial units. The washable finish saves us thousands in maintenance costs."— David P., Property Manager
Professional tip: For spray application on smooth surfaces, use a premium airless sprayer.
As an independent Cumbrian manufacturer, we prioritise quality over quantity. Every batch is carefully crafted using only the finest materials, no corner-cutting, no compromises.
The result? A paint that's built a loyal following across Britain, one satisfied customer at a time.
Get Weatherflex delivered to your door
Our technical team is here to help. Whether you're a homeowner tackling your first exterior project or a contractor specifying for commercial work, we'll make sure you get the right solution.
Technical support: Available Mon-Fri 8AM-5PMContact us: Click here
Two primary delivery options for smaller U.K MAINLAND orders (Typically under 100 Kg):
Standard 3-day service: £6.25 plus VAT (Note: Highlands Postcodes may be up to 5 working days)
Next Working Day*: £13.95 plus VAT (Not available to Highlands Postcodes)*Excludes weekends and public holidays
Cut-off time for “Next Working Day” orders to be processed is 12:00 noon. Once your goods have been despatched, you will normally receive a confirmatory e-mail with tracking details so that you can check the progress of your order. Details
If the surface is prepared correctly in accordance with the data sheet and regularly maintained, "Weatherflex" will last for 15 years.
The drier the better to ensure good adhesion to the substrate.
It depends on the condition of the surface to be painted. "Virgin" unpainted surfaces should be primed with "Weatherflex Stabilising Solution" to improve the coverage, adhesion and depth of colour of the "Weatherflex" paint on existing painted surfaces, spot apply "Weatherflex Stabilising Solution" to improve adhesion on areas where the old paint has flaked off during surface prep.
"Weatherflex" should not be applied at temperatures below 6 deg C or in damp I humid conditions. In winter especially always allow sufficient time (at least 4 hours) for the paint to cure before the evening dew point.
Textured "Weatherflex" is normally used to give a decorative sand effect to smooth or plain surfaces. Use "smooth" on pebble dash or textured renders.
Used it on a brickwork seems ok at the moment time wil tell easy to apply pleased with the result
Reviewed by Albert
Stunning quality and a wholeheartedly fantastic masonary paint.
Reviewed by Steve
This is so good you could easily use it anywhere an everywhere, the quality of this product is amazing, great application, brilliant coverage and fantastic solid colour
Used on house happy with paint and colour
Reviewed by Andrea
Remove loose paintRemove all existing loose paint either chemically with paint stripper or with a wire brush and scraper to make sure that you have a sound surface onto which to apply the "Weatherflex". It is not necessary to remove all existing paint – that which is still well bonded to the surface will normally provide an adequate base for "Weatherflex".
Neutralise Moss & MouldWhere green mould, lichens and moss have taken hold, spray or sponge thoroughly with Kingfisher "Bio Wash" to kill off the visible "green stuff" and also the invisible roots and spores which are embedded in the substrate. This is very important and will prevent re-growth underneath your new coating.
"Make Good" PointingCarefully examine the mortar joints for signs of decay and rake out any crumbly areas and re-point adding Kingfisher "Pointing Solution" to the mix for waterproofing, flexibility and adhesion. Pay special attention to repair of chimney stacks as these are a frequent source of moisture ingress. Phone us if in doubt.
Repair Weathered Bricks or StoneIf there are any "blown" brick faces or stones, these can be “faced up” as follows:
a. Priming MixIn a bucket mix ONE part sharp sand, ONE part ordinary cement with neat "Pointing Solution". This should be paddle mixed with a drill (400 to 600 rpm) until a "yoghurt consistency" is achieved. You then brush or stipple this grey primer onto the area with a masonry brush or similar. Leave this for around 20 to 30 minutes.
b. Repair MixMix up a stiff repair render of 1 part cement to 4 parts sand mixed with "Pointing Solution" and a little water. It is important to apply the repair render within half an hour of the primer mix to ensure "continuity of key". This method avoids the usual shrinkage cracks and "falling out".
Stabilising & PrimingWhere stone, brick or mortar may be slightly friable or "soft", such surfaces should be primed with "Weatherflex Stabilising Solution" to harden the surface and improve the adhesion of the "Weatherflex" coating. The same treatment should be used for "dusting" surfaces and flaking paint which cannot be adequately removed by wire brushing.
IMPORTANT"Weatherflex Stabilising Solution" must be applied to any new pointing or re-facing repairs prior to coating with "Weatherflex" to prevent the alkalinity in the mortar from discolouring the paint (because although mortar hardens within 24 hours, it takes up to two months for full chemical cure!). Where the wall substrate is non-porous in nature (e.g. engineering bricks or granite stone) you should apply "Weatherflex Stabilising Solution" to improve adhesion. If in doubt a small test area of both stabilising solution and paint should be applied to check compatibility with the surface and if possible left to weather. Note: This is especially important if there is a possibility that the surface might previously have been treated with a clear water repellent or similar.
Apply the Weatherflex ™"Weatherflex" requires 2 coats and can be applied by brush or roller. Apply with broad, even strokes and avoid "loading" the brush or roller, especially on the first coat. It can also be sprayed with some DIY sprayers but for high pressure spraying our "Kolourseal wall coating" range is specifically formulated for professional contractors. It is recommended to coat one elevation at a time and check the batch numbers, ensuring that tubs from the same batch number are matched up for the top coat or at least per elevation. Do not apply in temperatures below 8 °C. Always buy a tester pot to check the colour suitability BEFORE ordering the full size container(s).
COVERAGEThe coating should be applied using brush or roller, aiming for a coverage of 8-10 sq mtr/litre for smooth surfaces and 4-6 sq mtr/litre on rough surfaces. Do not use outside when conditions are below 5 deg C over 24 hours or if rain is imminent. The paint will be touch dry in approx 2 hours, allow 4-6 hours between coats. Clean all brushes and rollers immediately after use in warm soapy water.
All fields marked with an * are required. If you are sending a photo, please allow time for the contact form to upload the photo. Please do not click refresh after clicking send until the form is submitted.
Our wall stabilising solution stabilises friable mortar, hardens surfaces which have "gone soft" due to weathering and allows you to paint straight after re-rendering or pointing in preparation for the application of "Weatherflex". Improves adhesion and depth of colour finish.
Bio-Wash Moss Remover, is the maintenance professional’s choice for controlling troublesome moss growth on exterior hard surfaces like tarmac driveways, block pavers, sandstone paving slabs, concrete slabs, walls and much more.
Weatherflex Premium Masonry Paint provides superior waterproof protection for your home exterior. Covers brick, stone, render & pebbledash with a breathable, flexible coating that lasts 15 years. Available in 72 contemporary colours from our Lakes & Fells collection. Excellent coverage of 5-6m² per litre. Water-based, non-toxic formula that allows walls to breathe while keeping moisture out. Perfect for UK weather conditions. Next day delivery available. £37.02 inc. VAT.
